Geary's launch new John Deere 6M Series in Ireland
John Deere 6M Series tractors – which were hailed as filling many of the niches that the company did not already fully address, on their launch to the wider world back in June – are now available in Ireland.
The launch last June was a big move, for the new range spans what might be termed the business end of the market where the bulk of tractors are sold, and it had to be got right if Deere were to be able to compete all the way across this vital segment.
There is a distinct division within the company's range; the basic M Series tends to be lower spec machines that can be dressed up while the R series models leave the factory with higher specification and levels of operator convenience and comfort.
Budget-friendly Deere
Naturally, there is a premium to be paid for the R series. While this is usually accepted when purchasing a larger machine, with smaller machines there is usually more budget constraints, and this is where the M Series tractors come into their own.
Deere did not shirk from ensuring that all niches are covered in the 95-250hp bracket with the new tractors, for 27 models were released.
Whatever the size of the tractor, the controls will remain the same throughout.
These included four different frame sizes with either four or six cylinder engines being available, depending on power requirement.
The smallest frame size accommodates the 96-125hp engines, while the mid takes over at 130hp and goes up to 150hp, which is the largest four cylinder model.
There is a slight overlap at this point, for the six cylinder mid-frame steps in with a six cylinder block at 145hp.
Lemken are a popular brand at Geary's and are continually developing new implements such as this seeder.
The mid-sized frame tops out at 185hp while the long wheelbase models kick off at 175hp and stretch up to 250hp.
Deciding factors
There is a good deal of logic to this approach, for it puts as much emphasis on tractor size as it does engine power, which can be as important when matching a tractor to a task.
The M Series tractors from John Deere are targeted at small to mid-sized farms.
The 6M Series tractors are now available here in Ireland, and Geary's Garage Ltd, which covers the Munster and south Clare areas, has held two launch days of late to bring these models to their customers attention.
The second event took place at the company's Clarecastle, Co. Clare depot, which serves an area dominated by stock farms, making it a territory ripe for the new machines.
Geary's Garages Ltd represent John Deere throughout Munster and south Clare
The location appears to be proving fruitful, for the company is well on course to match its sales levels of previous years despite the present downturn in machinery sales.
Johnny Corkery of Geary's notes that another great benefit of the new range is that CVT – or AutoPwr as John Deere refers to it – is available on certain models, offering 40km/h or 50km/h as a road speed.
This New Generation 3120 was taken as a trade-in and is being restored in house with a view to completing a Mizzen to Malin Head charity run
John Deere are usually thought of as premium tractors and therefore a little beyond the means, if not the aspirations, of a good number of farmers.
This can become entrenched in the minds of potential customers, who may consider the brand being simply too expensive when looking for a new tractor.
This 7430 was originally used by a lime spreading contractor. Now with 32,000 hours on the clock, it is having a well-deserved engine rebuild
This perception has now been firmly addressed with the 6M series, which are described as fleet tractors and enable the manufacturer to fully compete with other mainstream brands in the most fought-over sector of the market.
Hashtags
Try Our AI Features
Explore what Daily8 AI can do for you:
Comments
No comments yet...
Related Articles
Agriland
14-06-2025
- Agriland
Wide choice and monitoring from Nokian Heavy Tyres
The majority of tractor tyres are much like the majority of tractors themselves, built primarily as ploughing machines to answer the most basic demand in growing crops – turning the soil. Yet, just as some manufacturers build tractors to better fulfil other duties, such as transport, Nokian Tyres of Finland make a range of tyres that suit a wide variety of niche applications in addition to general purpose farm use. The Heavy Tyres division of Nokian Tyres caters for a wide range of machines, including excavators and trucks The company's Heavy Tyres division serves many demanding applications, including mines and dockside cranes, with farming and forestry growing in importance as it extends its range further into the land industries. However, there is a good deal of stiff competition out there so, to differentiate itself from the crowd, Nokian sets out its stall as appealing to farming and contractors with a premium product for high-powered tractors and forestry equipment. A tyre type for all situations Naturally, a traditional-type tractor tyre with the usual deep-angled lugs features in their range, but there are also block tread tyres, flotation tyres, winter tyres, and hybrid types in between these more focussed items. Tyres for forestry applications are prominent in the range with puncture resistance and lateral grip being two of the major requirements for working in this environment. Tyre types include these singles to replace the twins on a rubber duck excavator There are those suitable for timber harvesters, with different types again for forwarders while other products are designed specifically to work with tracks and chains. When it comes to farming, the company is strongly promoting its Soil King VF tyre, which is currently available in 11 sizes with more fittings planned. At a recent demonstration in Finland, there was the opportunity to compare the Soil King VF performance around the company's test track near its factory at Nokia against a more road-orientated tyre. The cavalry connection This was no true test of an agricultural product, but as many larger tractors spend a good deal of time undertaking transport tasks, it still remains a valid window into their performance under one particular set of circumstances. The tyre the Soil King VF was up against was the company's Hakkapelliita TRI which – described as a block-patterned tyre for built environments – is hardly what one might expect to find on a farm tractor. The John Deere sported a set of Hakkapaliitta winter tyres, although all season versions are available However, they are available in 26 different sizes for tractors and eight different sizes for wheeled loaders, so there is certainly a market for them in the Nordic countries and beyond. To a tongue brought up to speak English, Hakkapeliitta is something of a mouthful, but it is the original brand name for Nokian's winter tyre range, whether car or heavy duty. The name refers to a light cavalryman of the 17th century. The horses bred to accompany the soldiers were strong and durable with their descendants – known as the Finnish Universal – being considered suitable for both draught work and riding. Mixed fleet Three tractors were available on the day – a small fleet which, unsurprisingly, featured a fellow Finn in the shape of a Valtra S415 fitted with a Central Tyre Inflation System. A Valtra S series was brought in to demonstrate the effect of tyre pressure on road handling This optional extra illustrated the flexibility of the Soil King VFs, as they could be reduced to 0.5 bar and still stay on the rim under load, with a much enlarged footprint to spread the weight and improve traction. Yet driving at any speed above a good trot at these low pressures was an unnerving experience for handling was, at best, imprecise, and over-heating of the tyre wall could result in damage to its structure. The Fendt 728 Vario on Soil King VFs gave a steady ride with only a hint of vagueness at the recommended pressure for road use With a more realistic 1.8 bar set, driving on tarmac became a far more sensible proposition and steering was quite responsive – yet it was not perfect with the tractor carrying an extra 1,500kg in rear wheel weights. Block tread stability Switching over to a John Deere 6R 185, fitted with the aforementioned Hakkapellita TRI rubber, road manners were considerably improved and the tractor would drive as well as any light truck if it had the equivalent suspension. The question then arises as to where such a tyre might fit into Irish agriculture? The softer winter compound is unlikely to be required, yet a harder wearing version – the TR2 – with a similar tread pattern and design ethos is also available for all-season use. Nokian tyres are already offered as an option on JCB Fastracs Obviously there might be demand from operators of JCB Fastracs, which spend a lot of time on the roads with occasional forays into the field. In these cases, such a tyre would be ideal and JCB already offer it as an option on the 4000 series. Hedge-cutting contractors are another outlet, and the tyres are already being used for this purpose in the UK where it is not just the road manners and wear characteristics which are appreciated, but also the minimisation of marks and imprints in softer ground and kempt verges. Tyre pressure monitors Nokian are also at the forefront of real-time tyre monitoring with its Intuitu smart tyres system. Two parameters are measured by a device stuck to the inside of the tyre: the first is pressure;and the second is temperature. The readings are transferred to a phone app by Bluetooth. The test mule for the Intuitu tyre monitoring system is a Fendt 824 Vario with blue wheel centres to indicate it is a trials machine While pressure is the most important feature of tyre use – affecting, as it does, efficiency, safety and overall performance – the temperature can be the first sign of things going wrong. This is not confined to a loss of pressure but can also be a result of tyre damage or incorrect alignment and is therefore a good indication of tyre health. The tyre sensor is stuck to the inside of the tread to monitor temperature and pressure Intuitu is available on all tractor products, enabling pressures to be checked regularly from a smartphone, removing the guesswork of visual inspection and highlighting problems at an earlier stage. It costs around €100 per tyre.
Agriland
13-06-2025
- Agriland
John Deere forage harvesters break the 1,000hp barrier
John Deere has recently announced a fulsome list of upgrades to its forage harvester range which rightly entitles them to being described as new machines. However, when making the announcement, the company slipped in the news of its latest engine option almost as an afterthought. There are two model ranges within Deere's forage harvester portfolio, the F8 models and the F9 machines. The engines in all the new forage harvesters have been uprated The F9 machines may be powered by John Deere's own JDX18 engine, yielding up to 820hp, or a Liebherr 24.2L V12, which powers the F9 900 and 1000 models, and it is this engine that delivers 1,020hp in the larger of the two. Further down the order, engine power has been increased across the whole range with the smallest F8 100 having 425hp at the entry-level end of the scale while the F8 600 now offers 645hp. Sitting comfortably The company has also paid a good deal of attention to adding further comfort for the operator and machine utility. The new cabs are said to offer a clearer view and greater comfort The ActiveSeat in the F8 and F9 series swivels 16° to the right and to the left for easy access and visibility. The optional ActiveSeatTM II adds fully adjustable electric controls, cooling and heating, a massage function, and active suspension technology that isolates up to 90% of vertical movements for a smooth ride. A new forage-harvester-specific menu on the G5 screen allows operators to quickly adjust the most relevant machine functions with one fingertip. The screen is 35% larger and 75% faster than previous displays, with a high definition 1080p screen. Quality forage The spout now can be rotated up to 230° for optimal unloading, while the redesigned steering system of the rear axle delivers a 6m turning radius for tighter – and therefore quicker – headland turns. There is also an Active Fill Control feature which utilises a stereo camera system to control the rotation and flap position of the spout, automatically tracking transport vehicles and aiming the crop into trailers for an optimal fill strategy. The new spout can be set to automatically track and fill trailers running alongside Included amongst the improvements is a new inoculant dosing system which works with HarvestLab sensor readings to optimise silage quality through adjusting the dosing rate. The system features a 50L insulated concentrate tank for concentrated additives as well as a 325L tank for high volume application and water.
Agriland
11-06-2025
- Agriland
New John Deere balers boast auto-weave feature
John Deere have recently updated its product ranges, with the round balers receiving additions that take them forward significantly. All models of the this latest generation of round balers from are now equipped with advanced ISOBUS capabilities, ensuring they can be fully integrated into the John Deere Operations Center. While many digital innovations might appear peripheral to everyday farming, these improvements can add a good deal of utility to the machines. The location of the bales can be mapped although they are not geo-tagged An optional moisture monitor measures the average moisture per bale in real-time and alerts the operator on the tractor display if the moisture content deviates from the pre-defined setting. Alongside the ability to track each bale's size and drop location, this data can be documented in the cloud, offering the ability to record the number of bales per field and create dry-matter maps – though, as always, it is up to the farmer to make the most of this information. Weave automation Two of the variable chamber models – the V452R and V462R – have been given a a 15% increase in driveline power intake, which Deere claims translates to an 8% increase in productivity in the field. The company's innovative weave automation feature was introduced in the US in February. Rather than automate the steering of the tractor as it passes down the windrow, a flexible drawbar automatically guides the baler left and right along the windrow, depending on how the chamber is filling, According to John Deere, this system creates consistent bales. The automatic weaving feature is said to ensure consistently shaped bales It also enables the machine to accurately follow curved windrows, even at the field corners as it tracks the cut grass, eliminating missed crop and reducing tractor manoeuvres. Also, the tighter turning radius makes manoeuvring the baler easier. The fast bale release system allows for unloading a bale and closing the gate in just three seconds, while the double-belt system as been upgraded to give 7% more compression. Built-in weighing on balers The wrapping baler models – C442R, C452R, and C462R – can now be specified with a built-in bale weighing system that is driven by strength gauges on each of the four transport table rollers, allowing for on-the-go measurement of each bale's weight. All new round balers now have hydraulically actuated knife engagement allowing the engaging or retracting the knives from the cab, while the higher knife engagement force makes sure all crop gets consistently cut.
